- Easy to install quad rail free float handguard for sale how to#
- Easy to install quad rail free float handguard for sale series#
The Mission First Tactical handguard we're installing here uses the standard barrel nut, so we'll put the same one back on later.
Some free-floated handguards come with a custom barrel nut, so depending on which handguard you choose, you might be reinstalling a new one instead of the original. You'll only need to reinstall the barrel nut itself. The barrel nut and delta ring will slide off the barrel as a single unit, so you'll need to separate the two. As it's going to be tight, it will be a lot easier to do by using a torque wrench inserted into the barrel nut wrench as shown in the picture.
Using a barrel nut wrench or armorers tool with a barrel nut wrench, remove the barrel nut using the righty-tighty, lefty-loosey direction. Use of this tool will ensure that your vise does not deform the upper receiver. The barrel nut is torqued on tight, so you'll want to mount the upper receiver in a vise using an upper receiver vise block. To get this out of the way, you'll need to remove the barrel nut. The next step will be to remove the delta ring. This will allow you to separate the gas tube from the front sight. Now you can drive the smaller gas tube pin out, again left to right. If you haven't already removed the gas tube pin, then the front sight will slide off the barrel with the gas tube attached. They can be sticky, so you might need to gently encourage it with a piece of wood or nylon hammer. Once the two lower pins are removed, you should be able to slide the front sight off the barrel. There's a smaller pin on the upper side that is used to fasten the gas tube to the front sight. The two larger pins under the sight hold the assembly to the barrel. Punch the pins out from the left side of the A2 sight toward the right. Just a heads up here, these pins can be notoriously difficult to remove, so use a cupped punch that won't deform the pins. This tool allows you to rest the front sight in a stable position so you can drive out the three pins that hold the sight to the barrel and gas tube to the front sight and gas block.
The easiest way to do this is to invest in a front sight block. This will need to come off - at least temporarily. If there is an optic installed, go ahead and take it off as we'll need to put the upper receiver in a vise in a couple of steps.įor purposes of this article, we'll assume that the rifle has a standard A2 gas block and front sight installed. Crush washers allow you to tighten the flash hider and time it correctly, so the non-slotted section is on the bottom.Īt this point, I think it's simpler to separate the upper and lower receivers. If it's a standard A2-style like this one, you'll want to use a brand new crush washer when reinstalling later, so be sure to have a supply of those on hand. Next, you'll want to remove the flash hider or muzzle brake. The delta ring is under some serious spring pressure, so if you plan on doing this a lot, invest a few bucks in a handguard removal tool - you won't regret that purchase. Simply pull the delta ring towards the receiver, and ease out each half of the handguard. The first step is to remove the standard plastic hand guard. Freeing the barrel from handguard stress allows it to operate independently of hand, sling, bipod or accessory pressure, thereby making it more consistently accurate shot to shot.
Easy to install quad rail free float handguard for sale how to#
With that in mind, let’s take a look at how to help your customer upgrade their stock AR plastic handguards to a more accurate - and sharper-looking - free-floated handguard model. After all, one of the great things about the AR-15 platform is its modularity. That makes for an opportunity to provide advice and sell add-on products. Many of your customers have them, and many of those who purchased ARs recently are newbies. While sales of new units have slowed to more rational and sustainable levels, the AR-type rifle remains a hot topic.
Easy to install quad rail free float handguard for sale series#
With that in mind, we’re launching a new series to help you and your staff learn and fine-tune skills that you can use to provide valuable services to your customers. Demonstrating, teaching, helping and sometimes doing are all things that you can use to make your business indispensable. One of the best ways to compete with online discount retailers is to provide unique service capabilities. If you sell and install a free-floated handguard like this Mission First Tactical model, it's a great time to offer a flash hider upgrade too.
0 kommentar(er)
